![Pengganti Ic 4017 Pengganti Ic 4017](http://tienthinhpro.wap.sh/tienich/led4017/traitim.gif)
Aflatoxigenic Aspergillus strains were isolated from all the seven regions of Hungary. parasiticus strains were able to synthesize aflatoxins. Based on morphological characteristics and the sequence analysis of the partial calmodulin gene, all isolates proved to be Aspergillus flavus, except four strains, which were identified as Aspergillus parasiticus. Fungi belonging to Aspergillus section Flavi were isolated in the ratio of 26.9% and 42.3% from soil and maize samples in 2013, and these ratios decreased to 16.1% and 34.7% in 2014. Our aim was to screen the presence of aflatoxigenic fungi in maize fields throughout the seven geographic regions of Hungary. SebÅ‘k, Flóra Dobolyi, Csaba Zágoni, Dóra Risa, Anita Krifaton, Csilla Hartman, Mátyás Cserháti, Mátyás Szoboszlay, Sándor Kriszt, Balázsĭue to the climate change, aflatoxigenic Aspergillus species and strains have appeared in several European countries, contaminating different agricultural commodities with aflatoxin. And hence the input given to pin X and Y is reflected on the channel 2 X2 and Y2 pins.Aflatoxigenic Aspergillus flavus and Aspergillus parasiticus strains in Hungarian maize fields. As you can see here, the channel 2 is selected by making A as 0 and B as 1. The above image shows the simulation of CD4052 in demultiplexer circuit, the complete working can be found in the video linked below.
#Pengganti Ic 4017 how to#
We have already discussed the how to select the channel using pins A and B in the above table. The output pins can either be X0,Y0 or X1,Y1 or X2,Y2 or X3,Y3 based on the value set on A and B pins. The CD4052 can be used as a 1:4 Demultiplexer also, that is it can take one input and provide it either one of the 4 output channels based on the channel select pins. So the input given to X1 and Y1 is reflected on the pins X and Y. Meaning the Channel 1 that is X1 and Y1 is selected. The complete working of a 4:1 MUX using the CD4052 simulation is shown in the video below, the image here shows a snapshot of it.Īs you can see in the above image, the channel select pins are 1 and 0 for A and B respectively. The state of the select pins and channel selection is shown in below table:
![Pengganti Ic 4017 Pengganti Ic 4017](https://i.ytimg.com/vi/1xeps2L0MPo/maxresdefault.jpg)
The output on the single channel is decided based on the channel select pins A and B. In our case the four Input channels are X0Y0, X1Y1, X2Y2 and X3 and Y3 and the single output channel is X,Y. The CD4052 can be used as a 4:1 Multiplexer, that is it can take inputs from 4-channel and convert it to single channel output based in the channel select pins. It can handle both analog and digital voltages hence can be used in Analog to Digital and Digital to Analog converters. The IC is commonly used in circuit where a 4:1 MUX or a 1:4 DEMUX is required in a Programmable Logic circuit Design. The IC CD4052 is a CMOS based high voltage Multiplexer and Demultiplexer IC. Note: Complete Technical Details can be found at the CD4052 datasheet given at the end of this page. Available in 16-pin PDIP, CDIP,SOIC, TSSOP packages.Supports both Analog and Digital Voltage.Negative power rail, normally connected to ground.Įnable pin – Must be pulled to ground for normal operation The IC supports both Analog and Digital voltages and hence widely used in many designs. It can either be used as a 4:1 Multiplexer or 1:4 Demultiplexer. The CD4052 is a 4-Channel Multiplexer and Demulitplexer IC.